金年会 金字招牌诚信至上,金年会 金字招牌诚信至上,金年会 金字招牌诚信至上,金年会 金字招牌诚信至上

 找回密碼
 注冊

QQ登錄

只需一步,快速開始

查看: 2432|回復: 9
打印 上一主題 下一主題

[分享] IBM筆記本報錯代碼及解決方法

跳轉到指定樓層
1#
sunfei08 發表于 2010-9-30 09:56:22 | 只看該作者 回帖獎勵 |倒序瀏覽 |閱讀模式 來自 中國江蘇南京

馬上注冊,結交更多好友,享用更多功能。

您需要 登錄 才可以下載或查看,沒有帳號?注冊

x
Symptom / Error (開機錯誤代碼) FRU / Action in Sequence(檢查范圍及解決方法)
. n9 d5 f' P# m8 i  t一、10*- s1 e9 F' L0 n! ^: H) C% A8 E
101
Interrupt failure;(中斷故障)
8 f8 ?/ l/ {) w! b. i1 a5 P6 ?
102Timer failure;(計時器故障)
! i, I7 {# B# }- W2 V& l103Timer interrupt failure; (計時器中斷故障)
$ C5 H" e! g) j' c0 X104Protected mode failure; (保護模式故障)! ^9 H3 V5 Y& Y, `1 K1 _3 N, }0 \
105Last 8042 command not accepted;
7 E; h/ H% P& A107NMI test failure;(NMI 測試失。3 `' q' v! P' Y% h
108Timer bus test failure.* l0 G5 Z- `0 K/ s6 D+ k
109
Low meg-chip select test. 1. System board. 主板問題)

! O& n) n( `2 A7 e二、11*6 L* ~- L: [7 S3 c% E5 ]% g. }
110
(Planar parity.) 內存奇偶校驗出錯)

" R& M1 I0 U# o9 I9 Q1 h1. Go to Memory Checkout1 B* A0 ]& g' X- y: \
2. DIMM card.7 n* d8 i* w# e- ?% u, S( q
3. Detach the expansion unit if it is attached to the computer.4. System board.) T" j9 `! x# _& g
111
(I/O parity.)# R. r& c- O2 k
1. Go to Memory Checkout
* F2 c4 i. G2 a2 K# k; M2 A2. Expansion unit or port replicator.
, I- w" O2 P4 l/ W3 \4 K3. System board.
$ ^; b# T! c5 Q+ d2 W; L( o+ T
二、
11**
1 K3 L7 u# d9 S1101
Serial_A test failure.A 串行口測試失。
: [/ M. _$ s8 V9 N: }4 U
1. Serial device (串行設備)
* E4 P% Q5 S, b% T2. Communication cable (相關通訊電纜). r+ a, X5 p. U# d8 r' Q
3. System board (主板)! v4 W" k+ \/ ?. \! u. ]
三、12**
. o  U. J8 j8 Y; V3 w1201
Serial_B test failure.B 串行口測試失。

8 N& G' r$ o9 x' b* WSystem board (infrared) (檢查主板:紅外線口)4 J7 C  R5 {1 E- }; `( }
四、15*/ |% a& W" @$ n- w- F0 t
158
(Hard disk password was not set even though the supervisor password is set.)3 ^. K! N9 m  Y$ a: s
(超級用戶密碼已設,但硬盤密碼沒有設置),設置硬盤密碼
,. X& j) p. [% v: S' ~6 r3 R
159
(Hard disk password is not set the same as the supervisor password.)
8 U. m6 e5 I7 L' y! a3 W# j' t8 x
(硬盤密碼與超級用戶密碼不一樣),設置正確的硬盤密碼
. K( b- o* I; \* w& e6 k+ v
五、16*( S2 f/ C- F" v
161
(Dead battery.) CMOS 電池不行)
! M, v0 `( e6 E& H4 g( Q( U
1. Go to Checking the Backup Battery4 e0 j7 D1 O% J8 }8 G
2. Backup battery.
CMOS 備份電池,在內存插槽旁邊)' t$ [' }5 F6 y6 f, J1 H" g
3. System board. (主板)
8 l8 @* D" X1 Z& Z+ [163(Time and date were not set.) (系統時間沒有設好或混亂). ^* A. Y+ I% w! \8 H
1. Set time and date.(設置正確的系 統時間)& F8 P* |  f! n. a3 E7 R% P
2. System board. (主板問題)# W/ `$ p9 _2 I$ k! y8 v. Q
六、17*7 F! p* \! |# O" O
173
(Configuration data was lost.) CMOS 設備配置信息丟失)
: p2 W9 W1 I: ~( F: _% W1 k+ Z# S; P
1. Select OK in the error screen; then set the time and date.(在 開機 ERROR 畫面上按OK,然后設置系統時間)8 U7 G' O1 ^' `/ ^' F
2. Backup battery. CMOS 電池需要更換)9 @, e$ j$ u2 ?* d& r0 P
3. System board. (主板問題)( S0 [% l3 j. G1 s0 J
174(Configuration errorPerform Checking the Installed Devices List before changing any FRUs.)+ x/ k1 s$ O! c" L+ U4 ]8 h/ L
1. Check device configuration., }1 d6 X* H. l, ]' L
2. Hard disk drive assembly.
3 G7 q' v) Q1 w8 |, C% ~3. System board.6 Q0 v0 l5 a' Y5 {
175
EEPROM CRC #1 error.- [8 {8 e1 C: V- M- x& c
177
Supervisor password check sum error.
. f/ U" Z' M. [/ J178
EEPROM is not functional. System board. (檢查主板)

9 x+ w! M2 X9 [# Q6 T' p) I% f% O七、17**
* d3 _' y+ s. a( x1701
Hard disk controller failure. (硬盤控制器故障)

; Y  f6 X6 ~  {* v. z) h* C; _1780, 1790Hard disk 0 error. (主硬盤有問題)
# N% ~! a: V+ |7 i) g# @: Y1781, 1791Hard disk 1 error.(從硬盤有問題)
8 y) O3 b+ l' R: J# Y, F# y8 M0 N1. Hard disk drive (檢查硬盤)
3 T5 b* P  {6 ]0 N! s' o6 Z9 T2. System board (檢查主板)4 M6 m6 Q4 G; t% b4 \
八、18*
. {8 S0 U( z( {/ t* D183
(Incorrect password entered at the supervisor password prompt.) (超級用戶開機密碼不對),Have the user examine the password.(請用戶檢查密碼)
  f, }, x/ z/ T+ d( Z
184(Power-on password check sum error.) Power-on 密碼有誤)
& J* o0 `8 B+ @0 I  lReset the power-on password in Easy-Setup.(重設Power-on 密碼)! }5 g- s# O* E. t
185(The startup sequence is not valid. Suspect that power was off when the startup sequence was being updated.) (系統啟動順序無效,懷疑是更新啟動順序時電源關掉). V, Q. h: L/ x0 t4 Q
Reset the startup sequence in Easy-Setup.(在Easy-Setup 重設啟動順序)+ K" E6 {6 i$ x$ [
186System board. (檢查主板)
$ ~, b- k5 ?, Z) _5 @& X: Y: C九、19*
7 D( z* k% h& t8 [& d190
(A depleted battery pack was installed when the power was on.) (開機時,機內筆記本電池已快耗盡了),Go to Checking the Battery Pack.(更換機內筆記本電池)
; ~! J! C/ Q% @4 z! q: x3 m
191(PM initialization error.) PM 初始化錯誤) System board. (檢查主板)
/ K1 _# @8 e0 O5 _9 M; O+ \192(Fan error.) CPU 散熱風扇故障)
- {# u3 b! H/ F+ `* Y9 t2 S. {1. Measure the voltage of the backup battery. If the voltage is not correct, replace the backup battery.(檢查CMOS 備份電池的電壓,電壓不行時更換電池)1 T2 u; ], W+ [8 \! F
2. Fan (更換CPU風扇)5 h* p. ]3 Q; i/ Z
3. System board (主板問題)- I$ Z' G3 E8 {, I7 N8 t- t: c, H
195(The configuration read from the hibernation area does not match the actual configuration.) (從休眠區域讀到的系統配置信息與實際配置不同)
% K5 m: g+ m" w, q; b4 oCheck if the configuration was changed. For example, check if the DIMM card is added.(檢查配置是否改動,內存有無增加等)
2 \8 i* b9 l4 j1 L/ A5 A- {+ U: C1 x# j196(A read error occurred in the hibernation area of the hard disk drive.) 從硬盤的休眠區域中讀寫時,發生錯誤)
& I" c" g$ f( Q# {0 j; p1. Run the hard disk drive test. (測試硬盤); u# i: Q# `5 Z  e  v9 g1 K# q
2. Hard disk drive.(檢查硬盤)! t# F" s# S# g8 j1 @3 ?7 @
199(Resume error.) ,System board. (主板問題)2 g, p, `! k, d) S. Y
十、2**(內存問題)
- O! y; F* {( [1 I$ Z' ^0 q6 Y: I201Memory data error.6 b1 ?$ t8 Q  O9 H
202
Memory line error 00-15.203
Memory line error 16-23.2 A- w: w2 D" a
205
Memory test failure on on-boardmemory.
) L% w0 |1 l5 |: I2 P221
ROM to RAM remap error.3 P7 n" ?( K  I7 i0 @9 u. E
1. Go to Memory Checkout.
+ o' y5 E5 [  y( G' v( E4 w2. DIMM card.
$ t9 }% |; y' l8 K3. System board.
0 \4 S0 T( C4 g! h3 k225
(Unsupported memory module.)
6 m( g+ @8 N% X2 w! ^" a1. Check if the supported DIMM is installed.
! Z' B: {9 j% l. \1 v! ~2. DIMM card.
8 `. g5 I7 X+ u/ n: ?& S! a  O) i: Q3 f% v6 K3. System board.
- @& }+ S9 |) H1 x& H  S
& ~% l# I# H3 @8 a( M2 [
十一、
3**
& s/ ^/ u% ?! W& @1 A8 d301, 303, 304, 305, 3XX
9 N1 s: l( O9 i& |301
:(Keyboard error. (筆記本鍵盤故障,301這個故障經常出現,往往是筆記本剛開機時,不小心按住鍵盤所造成的,一般只要重啟電腦即可;)
! z' q6 G- ^& P% p8 C
1. Go to Keyboard or Auxiliary Input Device Checkout/ a- |9 L$ w1 v5 i$ y& x! Q! K
2. Keyboard.: G4 X; W0 C' N' i+ S3 ]/ ]
3. External numeric keypad.
5 u7 f7 |( n) F! G2 ^% U4. External keyboard.! ~! R& ^# V" R" f9 i
5. Keyboard/mouse cable.
2 U% ?, Q/ ^. Z, Z6. System board.
" b2 z9 L( }! P2 K# {) v
, }  [6 l* U( f5 d5 l  P  c! L( ^
十二、6**
. u; h+ ^' G/ w: K3 f; ~601
(Diskette drive or controller error.) (軟驅或軟驅控制器故障)

8 ?$ s# M5 W" e) ?. w) `1. Go to Diskette Drive Checkout.0 h0 z2 O1 t. D+ I+ o  X
2. Diskette drive assembly.
(軟驅有沒有裝配好?)
3 F4 S( J- i# w9 p/ F; M, \/ Q3. Diskette.+ ?) W) ]2 |3 j9 Q0 [% S
4. System board.
(檢查主板
" b+ }* a3 ~" S: G2 ^. ~7 T! l  u4 k602(Diskette read error.); (軟驅讀故障)
$ `# w+ S; @. e0 [; d1. Go to Diskette Drive Checkout- L5 x3 c: b& g; c6 c( E1 k$ l1 Q4 S
2. Diskette.0 i0 l2 b4 O  E2 s" h
3. Diskette drive assembly.
(軟驅有沒有裝配好?)
8 c0 T1 S7 r+ l6 K% V+ F, n% c604(Unacceptable ID was read from the diskette drive.)3 M- b4 O3 N! q+ U4 z
1. Go to Diskette Drive Checkout8 u0 G8 }# D, w; i8 G* _  U# P
2. Diskette drive assembly.6 o2 y3 S8 i" f: I% e% T, l. ~0 ]
3. System board.
# ]# v  S8 t# [* s9 }) J. k& r' ]6 n. z
十三、
24**6 ~  n% d$ g" W* _- A! W
2401
(System board video error.)(主板顯示部分有問題)

, x' P; M! ]7 J) P; X( gSystem board. (檢查主板相關部分)  \5 ~( w" t: k0 h
十四、808*% ?- \2 b" b' v3 z, h
8081
PCMCIA presence test failure.(PCMCIA revision number also checked.)
, K: C; J; `0 D* X. S8082
PCMCIA register test failure.
7 K' D# e4 y  W2 a" ~1. PC Card slot assembly.
" X- |' C! a# g% y- h2. PCMCIA device.+ P3 Z5 b6 H' {: {1 E& K7 W
3. System board.
* y5 L' B$ x, `, X. S5 Z
! P& j% Q. m2 o9 I: h+ l
十五、860* (Pointing device error when TrackPoint is disabled.) (當指點桿禁用時,外接的指點設備有故障);
) W! p/ T  H, Q0 V1 [
8601System bus error-8042 mouse interface.. M! s( e6 ?5 @; g- _1 [. X
8602
External mouse error.(外接鼠標故障);

- E! i  R7 x* o5 d8603System bus error or mouse error. (總線或鼠標故障)3 Q: {8 G5 a! b  t4 h6 N* U
1. External mouse. (檢查外接鼠標);5 Y7 Q  f: x& Q1 S+ D, b
2. External keyboard. (檢查外接鍵盤);
. O8 t7 ^- @+ P; O4 V6 c  g7 O3. System board.(檢查主板);
) E1 i9 q! u/ d( E5 {% y
3 E. X2 `  I6 C* h5 [) l
2#
PANPPP 發表于 2010-9-30 10:06:32 | 只看該作者 來自 中國山西太原
這個就不用發了吧  而且也不全  
3#
xinghenzilei 發表于 2010-9-30 11:44:14 | 只看該作者 來自 中國四川成都
還多好的呢
4#
wcd19810927 發表于 2010-9-30 13:24:33 | 只看該作者 來自 中國廣東廣州
在學習成長中
5#
lin49045 發表于 2010-10-5 03:27:00 | 只看該作者 來自 中國臺灣
筆記本維休的好幚手
6#
zhangfeifei1014 發表于 2010-10-5 10:34:04 | 只看該作者 來自 中國山東菏澤
謝謝。還挺不錯的。。。。學習了。。
7#
allen1987 發表于 2010-10-5 17:47:39 | 只看該作者 來自 中國山東濟南
既然人家都發了,辛苦總是有的,謝謝啊
8#
恒信偉杰科技 發表于 2010-10-8 13:14:51 | 只看該作者 來自 中國河北唐山
謝謝 分享  
9#
pengzhichao38 發表于 2010-10-9 01:14:35 | 只看該作者 來自 中國廣東惠州
真是有心人呀。這個也發來這里,,呵呵
10#
明達明 發表于 2010-10-9 12:27:52 | 只看該作者 來自 中國北京
學習了。。。。。。。。。!
您需要登錄后才可以回帖 登錄 | 注冊

本版積分規則

快速回復 返回頂部 返回列表
松江区| 乐东| 湖南省| 绩溪县| 察哈| 泾川县| 抚宁县| 兴隆县| 应用必备| 惠水县| 两当县| 武平县| 尚志市| 靖西县| 铜山县| 莱西市| 江华| 庆阳市| 洪洞县| 冀州市| 衡阳市| 吴川市| 凭祥市| 张家界市| 莒南县| 龙游县| 罗江县| 石家庄市| 监利县| 札达县| 康平县| 浏阳市| 大埔县| 乐昌市| 兖州市| 乌兰察布市| 武夷山市| 阳城县| 仁寿县| 堆龙德庆县| 清徐县|