Fixing a dead Seagate 80gb drive
In case this helps someone else:
A colleague was given a broken PC. They were told that the power supply had blown, and the owner decided to buy a whole new PC rather than bother to fix it. I was asked to to try to get it to go. I tried a different ATX power supply and after some false starts I got most of the PC going again. It had two internal drives; a 10GB IBM drive plus a Seagate 80gb (ST380023A Barracude V). One thing I did find was that even with a new ATX PSU, the PC would not turn on with just the power of the 80gb drive connected. There was something seriously wrong with the 80gb drive. Anyway, I returned the PC and said both the power supply and the 80gb drive were broken, so they'd at least have to get a new PSU. I kept the 80gb drive since it was 'junk'.
But I was quite curious about the 80gb drive. I measured across the power connector. Between +5V and GND was some resistance, but +12V to GND seemed like a short circuit. Fortunately I actually had a working Seagate ST380023A Barracude V drive in another machine, so I pulled it out to compare. Interestingly this drive was bought from the same shop during the same month (per the warranty sticker) and had the same firmware version, but the logic boards were actually slightly different. Anyway, on my working drive, I traced where the +12V line went and found a few things it connected to. One of these was a little black square with markings BUX C240 with two pins on it (which I think is a diode). Its down near where the Power supply connector comes in. By desoldering one end of this from the dead hard drive, I could see that the short circuit between +12V and GND was removed. I have a diode tester on my multimeter and I could see that the BUX C240 was shorted out. My working 80gb drive had a similarly placed black square which I could see was not shorted out. It had the markings BUF C242 I think. I then scrounged through my junk pile and found an old 630MB hard drive that was dead and desoldered a diode from it (well I think it was a diode - it was a black square with a line on one end and had two pins on it). I can't remember what the markings were. I soldered it in place of the BUX C240 on the dead drive making sure the line on the packaging was oriented the same way.
I then powered it on and suffice to say it now works perfectly. I have been told by more wise electronics experts that the diode may be a zener diode to provide over voltage protection and that my generic replacement might not protect it from over voltage ... but hey it works for now.
Update (Dec 2004)
I came across a Seagate 40gb drive in an online auction advertised as:
Was working one day then stopped during a storm - never to go again
Of course, I had to bid on it to see whether it had the same seized diode fault ... didn't I? Well, NZ$7.50 later I had said 40Gb drive. This time it was shorted out between +5V and GND. Between +12V and ground was fine. Poking around with my multimeter I soon found a diode that was shorted. I replaced the diode and the drive seems to work fine now. Too easy.作者: miminzhang 時間: 2007-11-12 11:12 看不懂作者: kkk9999 時間: 2007-11-12 11:41
english ,作者: 夜_孤寒 時間: 2007-11-12 12:20 衰~作者: tywjh 時間: 2007-11-12 12:34 標題: 機器翻譯的分析著看! 修理死了的Seagate 80gb開車
以防這幫助另外的某人:
一位同事被給壞掉的PC。
他們被告訴電源已經刮，并且主人決定了而不是麻煩給全部買新PC修理它。
我被問到試著讓它走。
我試用了不同的ATX電源并且在一些不成功的開始以后我得到了再走的PC的大多數。
它有了2內在的開車;
加一Seagate 80gb的10GB IBM開車(ST380023A Barracude V)。
我確實發現了那的一件事情是甚至與一新的ATX PSU，與驅動器連結了的80gb的只是權力PC將不開。
有隨80gb開車嚴重錯誤的一些東西。
不管怎樣,我返回了PC并且說電源和80gb開車被打破,因此他們不得不將至少得到一新的PSU。
自從它是我堅持了80gb開車“垃圾”。
但是我是關于80gb相當好奇開車。
越過權力連接器我測量了。
在+ 5V和GND之間是一些抵抗，但是象一條短路一樣到GND的+ 12V似乎了。
我實際上幸運地讓了一工作的Seagate ST380023A Barracude V在另外的機器開車,因此我外面拉了它比較。
從同樣的的商店在同樣的的月期間這開車有趣地被買(每擔保滯銷物)并且有同樣的的韌件版本,但是邏輯板是實際上稍微不同。
不管怎樣,在我的工作的開車上，我在+ 12V行去找了它連結了到的一些事情的地方跟蹤了。
這些的之一是有有在它上的2枚大頭針的標記BUX C240的稍黑的平方(我認為它是一個二極管)。
它的下面在在哪兒附近電源連接器進來。
到從死了的硬盤的這的desoldering一結束為止，我能看見在+ 12V和GND之間的短路被移開。
在我的萬用表上我有二極管考試者并且我能看BUX C240 shorted外面。
我的工作的80gb開車有了我能看見的一個同樣被放置了黑平方外面不是shorted。
它有了我認為那的標記BUF C242。
通過我的垃圾堆積我那時搜尋了并且從它發現了是死了的一塊舊的630MB硬盤和desoldered一個二極管(很好我認為它是一個二極管它是有在一結束的行的一個黑平方并且在它上有了2枚大頭針)。
我不能記得標記是什么。
代替BUX C240在死了的開車上我錫焊了它在包裝上確信行是面向的同樣的的方法。
我那時產生動力它上并且足以做說它現在完美地工作。
我被二極管可以是一個禪宗二極管電壓保護上提供并且我的普通的代替可能不阻止它超過電壓的更明智的電子學專家已經告訴...
但是嗨它為現在盡力。
校正(2004年12月)
在被做廣告了作為的一次聯機的拍賣我碰到了Seagate 40gb開車:
有天正在工作然后在暴風雨期間停止了永不再走
當然,我不得不求包它審實它有了同樣的抓住的二極管過錯...
我？
很好,以后我已經說的NZ$7.50 40Gb開車。
這次它shorted外面在+ 5V和GND之間。
在+ 12V和地面之間是杰出的。
用我的我快發現了一個二極管那那的萬用表到處尋找shorted。
我代替了二極管并且開車似乎現在工作正常。
太容易。作者: hongyan27 時間: 2007-11-12 15:50
啥呀亂了吧唧的作者: 嘰哩 時間: 2007-11-12 17:10
樓上的翻譯的太好了，還是看不懂，呵呵作者: 初級學者99 時間: 2007-11-14 23:29
暈啊，難懂啊作者: 自由逍遙人 時間: 2007-11-16 10:32 作者: wen1234500 時間: 2007-11-16 22:43 俺可不是文化人作者: lanseyulin 時間: 2007-11-22 16:46
翻譯的太好了，還是看不懂，呵呵作者: 紙上談兵 時間: 2007-11-22 19:56
看不懂請高人給翻一下吧作者: xiongwcp 時間: 2007-11-26 16:16 作者: yangkking 時間: 2007-12-2 21:19
俺可不是文化人作者: H.WAVE 時間: 2007-12-4 13:16
想學習一下，但看不懂，作者: gk_1978 時間: 2007-12-5 12:52
那個翻譯就軟件翻譯的，看懂了才怪
軟件翻譯普通的還成，專業的就不用想了作者: tse 時間: 2007-12-8 23:05
看不懂！翻譯不來！無奈！作者: sword577 時間: 2007-12-10 12:06
餓~~~~什么跟什么都不知道作者: guohang1112 時間: 2007-12-12 09:02
kanbudongya作者: ling136841 時間: 2007-12-15 23:46 標題: 支持哈大哥！ 支持哈大哥！作者: yesehei 時間: 2007-12-15 23:48
暈！什么啊 ，看不懂，中文比英文還難看懂��！作者: suntom 時間: 2007-12-16 14:49
更換了電壓控制芯片而已....................作者: suntom 時間: 2007-12-16 14:50
............................作者: liaoya 時間: 2007-12-16 15:35 看不懂作者: liaoya 時間: 2007-12-16 15:36 作者: yzcg 時間: 2007-12-20 11:29
何必弄個英文來糊弄咱們呢？作者: jxc1689 時間: 2007-12-21 11:44
看不懂的 作者: 藍冰369 時間: 2007-12-22 12:43
誠心不給我們看呀作者: kw858 時間: 2007-12-23 21:21
換了個二極管 挺簡單的作者: x12345x 時間: 2008-1-7 11:19
看不懂 :o作者: yuminjiang 時間: 2008-1-7 12:53
不翻譯還好點，一翻譯全看不懂作者: 南極翁 時間: 2008-1-7 15:57
希望一樓最好是用漢語,熟讀英語的人還是不多啊.這是中華論壇,希望網友用漢語發帖子.謝謝作者: 2405032 時間: 2008-1-11 15:23
修理死的希捷80gb驅動
，萬一這幫助別人：
給了A同事一臺殘破的個人計算機。 他們告訴電源吹了，并且所有者決定買一臺整體新的個人計算機而不是麻煩修理它。 我請求對設法得到它是。 我嘗試了不同的ATX電源，并且，在一些錯誤開端我得到了再之后去大多數的個人計算機。 它有二內部驅動; 10GB IBM驅動加上希捷80gb (ST380023A Barracude V)。 我發現的一件事是那甚而與新的ATX PSU，個人計算機不會(huì )打開與被連接的80gb驅動的力量。 嚴重錯誤有某事與80gb驅動。 無論如何，我退回個人計算機并且說電源和80gb驅動是殘破的，因此他們將至少必須得到新的PSU。 因為它是‘破爛物’，我保留了80gb驅動。
衰~
看不懂
