系統

開機顯顯示，error loading operating system,這是什么故障，

重動時錯誤加載!!!

參考資料::::::
maxtor官方：Suggestions to Resolve the Condition:
1)Apply power to the computer. 開機（不插硬盤）。
2)Access the system BIOS. Set the drive type as None or Not Installed. Load BIOS Defaults .Load SETUP Defaults .在BIOS里，把硬盤設為NONE。
3)Save the BIOS changes and reboot the PC to a System Boot Diskette. 用啟動盤重啟機。
4)Shut down the PC after the memory count is displayed. 檢測完內存后關機。
5)Reconnect the power and interface cables to the hard drive. 重新插上硬盤電源和數據線。
6)Access the System BIOS. 進入BIOS。
7)Auto-Detect the hard drive. Ensure that the LBA Mode option is enabled. 設為自動檢測硬盤。確認LBA模式無誤。
8)Save the BIOS changes and boot the PC with a System Diskette. 軟盤啟動。
9)Partition and format the hard drive via the operating system. 分區格式化。
10)Reboot the system. On bootup, the screen should read: 重啟機，顯示如下：
Verifying DMI Pool Data  Update Successful
11)The system should continue booting normally. 正常。

Other Possible Solutions:

1)Apply power to the computer. 開機。
2)Access the System BIOS. 進入BIOS。
3)Disable both the Internal and External CPU Cache. These features are located in either the "BIOS Features" or "Advanced Settings" options of the BIOS Setup. NOTE: Consult the System or Motherboard User\'s Manual for exact location of the Internal and External CPU Cache settings. 參考系統或主板說明，在"BIOS Features"或 "Advanced Settings"選項里，將內/外部CPU Cache設置為不可用。
4)Save the BIOS changes and reboot the PC to a System Boot Diskette. On bootup, the screen should read: 重啟機，顯示如下：
Verifying DMI Pool Data   Update Successful
The system should continue booting normally. 可以正常引導。
7)After the system successfully boots, re-start the PC and access the system BIOS.
Enable the External CPU Cache. This feature is located in the "BIOS Features" or "Advanced Settings".
NOTE: Consult the System or Motherboard User\'s Manual for exact location of the External CPU Cache setting.成功引導后，重啟機，在BIOS里將CPU的兩個項恢復為enable。
! WARNING ! User\'s MUST re-enable this feature for optimal system performance. 該步驟必須執行。
8)Save the BIOS changes and reboot the PC to a System Boot Diskette. On bootup, the screen should read:
Verifying DMI Pool Data
Update Successful
The system should continue booting normally.
再重啟，可正常使用。

error 系統出錯了，

從安全模式看看！

回復 xinghenzilei 的帖子

一般是由于DOS引導扇區的錯誤引起的。當硬盤的主引導分區檢查正確后，根據可自舉分區中指出的分區起始地址讀DOS系統引導扇區，若讀操作失敗，則給出error load operation system的出錯信息，若能正確讀出DOS引導扇區，則系統將檢查引導扇區的最后兩個字節是否為有效標志 55AA
   

回復 zbp 的帖子


   

回復 xinghenzilei 的帖子


    造成該故障的原因是DOS引導記錄出現錯誤。DOS引導記錄位于邏輯0扇區，是由高級格式化命令FORMAT 生成的。主引導程序在檢查分區表正確之后，根據分區表中指出的DOS分區的起始地址，讀DOS引導記錄，若連續讀5次都失敗，則給出"Error loading operating system"的錯誤提示，若能正確讀出DOS引導記錄，主引導程序則會(huì )將DOS引導記錄送人內存0:7C00h處，然后檢查DOS引導記錄的最后兩個字節是否為55AAH，若不是這兩個字節，則給出“Missing operation system"的提示。一般情況下用NDD修復即可。若不成功，可以用sys c:命令重寫DOS引導記錄。

上百度看看